card10.c 6.01 KB
Newer Older
1
2
#include "pmic.h"
#include "bosch.h"
3
#include "display.h"
4
#include "portexpander.h"
5
6
7
8
9
10

#include "bhy_uc_driver.h"
#include "Bosch_PCB_7183_di03_BMI160_BMM150-7183_di03.2.1.11696_170103.h"
#include "bme680.h"
#include "bma400.h"
#include "bhy.h"
schneider's avatar
schneider committed
11
#include "leds.h"
12
13
14

#include "mxc_config.h"
#include "board.h"
15
#include "pb.h"
16
17
18
19
20
21
22
23
24
25
26

#include "tmr_utils.h"
#include "i2c.h"
#include "rtc.h"
#include "spi.h"
#include "gpio.h"

#include <stdio.h>
#include <stdint.h>
#include <string.h>

27
28
29
30
/* XXX: The display supports max 15 Mhz, but we have stability issues at that rate.
 * Current suspicion is that the SDK is buggy.
 *
 * At 12 MHz things seem stable*/
31
#define SPI_SPEED (12 * 1000 * 1000) // Bit Rate. Display has 15 MHz limit
32

33
34
35
const gpio_cfg_t bhi_interrupt_pin = {
	PORT_0, PIN_13, GPIO_FUNC_IN, GPIO_PAD_PULL_UP
};
36

37
38
void card10_init(void)
{
39
	printf("card10 init...\n");
40

41
42
43
	//Setup the I2CM
	I2C_Shutdown(MXC_I2C0_BUS0);
	I2C_Init(MXC_I2C0_BUS0, I2C_FAST_MODE, NULL);
44

45
46
	I2C_Shutdown(MXC_I2C1_BUS0);
	I2C_Init(MXC_I2C1_BUS0, I2C_FAST_MODE, NULL);
47

48
	portexpander_init();
49

50
	GPIO_Init();
51

52
	PB_Init();
53

54
55
56
57
58
	pmic_init();
	pmic_set_led(0, 0);
	pmic_set_led(1, 0);
	pmic_set_led(2, 0);
	TMR_Delay(MXC_TMR0, MSEC(1000), 0);
59

60
61
62
	while (RTC_EnableRTCE(MXC_RTC) == E_BUSY)
		;

63
	// Enable 32 kHz output
64
65
66
67
68
69
70
71
	while (RTC_SquareWave(
		       MXC_RTC,
		       SQUARE_WAVE_ENABLED,
		       F_32KHZ,
		       NOISE_IMMUNE_MODE,
		       NULL) == E_BUSY
	)
		;
72

73
74
75
76
77
	if (RTC_GetSecond() < 1546300800UL) {
		while (RTC_Init(MXC_RTC, 1546300800UL, 0, NULL) == E_BUSY)
			;
	}

78
79
	// Enable SPI
	sys_cfg_spi_t spi17y_master_cfg;
80

81
82
83
84
	spi17y_master_cfg.map = MAP_A;
	spi17y_master_cfg.ss0 = Enable;
	spi17y_master_cfg.ss1 = Disable;
	spi17y_master_cfg.ss2 = Disable;
85

86
87
88
89
90
	if (SPI_Init(SPI0, 0, SPI_SPEED, spi17y_master_cfg) != 0) {
		printf("Error configuring SPI\n");
		while (1)
			;
	}
91

92
93
94
95
96
	if (SPI_Init(SPI2, 0, SPI_SPEED, spi17y_master_cfg) != 0) {
		printf("Error configuring SPI\n");
		while (1)
			;
	}
schneider's avatar
schneider committed
97

98
	display_init();
99

100
	leds_init();
101

102
	GPIO_Config(&bhi_interrupt_pin);
103
104
105
106
}

static uint32_t ecg_read_reg(uint8_t reg)
{
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
	spi_req_t req;
	uint8_t tx_data[] = { (reg << 1) | 1, 0, 0, 0 };
	uint8_t rx_data[] = { 0, 0, 0, 0 };
	req.tx_data       = tx_data;
	req.rx_data       = rx_data;
	req.len           = 4;
	req.bits          = 8;
	req.width         = SPI17Y_WIDTH_1;
	req.ssel          = 0;
	req.deass         = 1;
	req.ssel_pol      = SPI17Y_POL_LOW;
	req.tx_num        = 0;
	req.rx_num        = 0;

	SPI_MasterTrans(SPI0, &req);

	return (rx_data[1] << 16) | (rx_data[2] << 8) | rx_data[3];
124
125
126
127
}

void card10_diag(void)
{
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
	uint8_t dummy[1] = { 0 };
	// "7-bit addresses 0b0000xxx and 0b1111xxx are reserved"
	for (int addr = 0x8; addr < 0x78; ++addr) {
		// A 0 byte write does not seem to work so always send a single byte.
		int res =
			I2C_MasterWrite(MXC_I2C0_BUS0, addr << 1, dummy, 1, 0);
		if (res == 1) {
			printf("Found (7 bit) address 0x%02x on I2C0\n", addr);
		}

		res = I2C_MasterWrite(MXC_I2C1_BUS0, addr << 1, dummy, 1, 0);
		if (res == 1) {
			printf("Found (7 bit) address 0x%02x on I2C1\n", addr);
		}
	}

	if (bhy_driver_init(bhy1_fw)) {
		printf("Failed to init bhy\n");
	} else {
		/* wait for the bhy trigger the interrupt pin go down and up again */
		while (GPIO_InGet(&bhi_interrupt_pin))
			;
		while (!GPIO_InGet(&bhi_interrupt_pin))
			;

		/* the remapping matrix for BHI and Magmetometer should be configured here to make sure rotation vector is */
		/* calculated in a correct coordinates system. */
		int8_t bhy_mapping_matrix_config[3 * 3] = { 0, -1, 0, 1, 0,
							    0, 0,  0, 1 };
		int8_t mag_mapping_matrix_config[3 * 3] = { -1, 0, 0, 0, 1,
							    0,  0, 0, -1 };
		bhy_mapping_matrix_set(
			PHYSICAL_SENSOR_INDEX_ACC, bhy_mapping_matrix_config
		);
		bhy_mapping_matrix_set(
			PHYSICAL_SENSOR_INDEX_MAG, mag_mapping_matrix_config
		);
		bhy_mapping_matrix_set(
			PHYSICAL_SENSOR_INDEX_GYRO, bhy_mapping_matrix_config
		);

		/* the sic matrix should be calculated for customer platform by logging uncalibrated magnetometer data. */
		/* the sic matrix here is only an example array (identity matrix). Customer should generate their own matrix. */
		/* This affects magnetometer fusion performance. */
		float sic_array[9] = { 1.0, 0.0, 0.0, 0.0, 1.0,
				       0.0, 0.0, 0.0, 1.0 };
		bhy_set_sic_matrix(sic_array);
	}

	struct bme680_dev gas_sensor;
	gas_sensor.dev_id   = BME680_I2C_ADDR_PRIMARY;
	gas_sensor.intf     = BME680_I2C_INTF;
	gas_sensor.read     = card10_bosch_i2c_read;
	gas_sensor.write    = card10_bosch_i2c_write;
	gas_sensor.delay_ms = card10_bosch_delay;
	gas_sensor.amb_temp = 25;

	int8_t rslt = BME680_OK;
	rslt        = bme680_init(&gas_sensor);
	if (rslt != BME680_OK) {
		printf("Failed to init BME680\n");
	}

	struct bma400_dev bma;
	bma.intf_ptr = NULL; /* To attach your interface device reference */
	bma.delay_ms = card10_bosch_delay;
	bma.dev_id   = BMA400_I2C_ADDRESS_SDO_LOW;
	bma.read     = card10_bosch_i2c_read_ex;
	bma.write    = card10_bosch_i2c_write_ex;
	bma.intf     = BMA400_I2C_INTF;

	rslt = bma400_init(&bma);
	if (rslt == BMA400_OK) {
		printf("BMA400 found with chip ID 0x%X\r\n", bma.chip_id);
	}
203

schneider's avatar
schneider committed
204
#if 0
205
206
207
208
    for(int i=0; i<0x20; i++) {
        uint32_t val = ecg_read_reg(i);
        printf("ECG: %02x: 0x%06x\n", i, val);
    }
schneider's avatar
schneider committed
209
#else
210
211
	uint32_t val = ecg_read_reg(0xf);
	printf("ECG: %02x: 0x%06lx (should be 0x5139a0)\n", 0xf, val);
schneider's avatar
schneider committed
212
#endif
213
}
214

215
216
217
218
219
void core1_start(void)
{
	//MXC_GCR->gp0 = (uint32_t)(&__isr_vector_core1);
	MXC_GCR->gp0 = 0x10080000;
	MXC_GCR->perckcn1 &= ~MXC_F_GCR_PERCKCN1_CPU1;
220
221
}

222
223
224
void core1_stop(void)
{
	MXC_GCR->perckcn1 |= MXC_F_GCR_PERCKCN1_CPU1;
225
226
}

227
228
void card10_poll(void)
{
229
	pmic_poll();
230
}
231

232
233
234
235
236
237
238
239
240
241
242
243
244
void card10_reset(void)
{
	printf("Resetting ...\n");
	/*
        * Give the UART fifo time to clear.
        * TODO: Do this properly
        */
	for (int i = 0; i < 0x1000000; i++) {
		__asm volatile("nop");
	}
	MXC_GCR->rstr0 = MXC_F_GCR_RSTR0_SYSTEM;
}

245
246
void GPIO0_IRQHandler(void)
{
247
	GPIO_Handler(PORT_0);
248
249
250
251
}

void GPIO1_IRQHandler(void)
{
252
	GPIO_Handler(PORT_1);
253
254
255
256
}

void GPIO2_IRQHandler(void)
{
257
	GPIO_Handler(PORT_2);
258
259
260
261
}

void GPIO3_IRQHandler(void)
{
262
	GPIO_Handler(PORT_3);
263
}