Commit 32188c50 authored by Viktar Palstsiuk's avatar Viktar Palstsiuk Committed by Øyvind Harboe
Browse files

target library: configuration files for openocd tested with Atmel SAM-ICE V6 JTAG.



Signed-off-by: default avatarØyvind Harboe <oyvind.harboe@zylin.com>
parent 527e073b
################################################################################
#
# Generated for Atmel AT91SAM9RL-EK evaluation board using Atmel SAM-ICE (J-Link) V6
#
# Atmel AT91SAM9RL : PLL = 200 MHz, MCK = 100 MHz
# OSCSEL configured for external 32.768 kHz crystal
#
# 32-bit SDRAM : 2 x Micron MT48LC16M16A2, 4M x 16Bit x 4 Banks
#
################################################################################
# We add to the minimal configuration.
source [find target/at91sam9rl.cfg]
$_TARGETNAME configure -event reset-start {
# At reset CPU runs at 32.768 kHz.
# JTAG Frequency must be 6 times slower if RCLK is not supported.
jtag_rclk 5
halt
# RSTC_MR : enable user reset, MMU may be enabled... use physical address
mww phys 0xfffffd08 0xa5000501
}
$_TARGETNAME configure -event reset-init {
mww 0xfffffd44 0x00008000 # WDT_MR : disable watchdog
mww 0xfffffc20 0x00004001 # CKGR_MOR : enable the main oscillator
sleep 20 # wait 20 ms
mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main oscillator
sleep 10 # wait 10 ms
mww 0xfffffc28 0x2031bf03 # CKGR_PLLR: Set PLL Register for 200 MHz
sleep 20 # wait 20 ms
mww 0xfffffc30 0x00000101 # PMC_MCKR : Select prescaler (divide by 2)
sleep 10 # wait 10 ms
mww 0xfffffc30 0x00000102 # PMC_MCKR : Clock from PLL is selected (100 MHz)
sleep 10 # wait 10 ms
# Increase JTAG Speed to 6 MHz if RCLK is not supported
jtag_rclk 6000
arm7_9 dcc_downloads enable # Enable faster DCC downloads
mww 0xfffff670 0xffff0000 # PIO_ASR : Select peripheral function for D16..D31 (PIOB)
mww 0xfffff604 0xffff0000 # PIO_PDR : Disable PIO function for D16..D31 (PIOB)
mww 0xffffef20 0x00010002 # EBI_CSA : Assign EBI Chip Select 1 to SDRAM, VDDIOMSEL set for +3V3 memory
mww 0xffffea08 0x85227259 # SDRAMC_CR : Configure SDRAM (2 x Micron MT48LC16M16A2 : 4M x 16Bit x 4 Banks)
mww 0xffffea00 0x1 # SDRAMC_MR : issue a NOP command
mww 0x20000000 0
mww 0xffffea00 0x2 # SDRAMC_MR : issue an 'All Banks Precharge' command
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue 8 x 'Auto-Refresh' Command
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x4
mww 0x20000000 0
mww 0xffffea00 0x3 # SDRAMC_MR : issue a 'Load Mode Register' command
mww 0x20000000 0
mww 0xffffea00 0x0 # SDRAMC_MR : normal mode
mww 0x20000000 0
mww 0xffffea04 0x2b6 # SDRAMC_TR : Set refresh timer count to 7us
}
######################################
# Target: Atmel AT91SAM9RL
######################################
if { [info exists CHIPNAME] } {
set _CHIPNAME $CHIPNAME
} else {
set _CHIPNAME at91sam9rl
}
if { [info exists ENDIAN] } {
set _ENDIAN $ENDIAN
} else {
set _ENDIAN little
}
if { [info exists CPUTAPID ] } {
set _CPUTAPID $CPUTAPID
} else {
# force an error till we get a good number
set _CPUTAPID 0x0792603f
}
reset_config trst_and_srst separate trst_push_pull srst_open_drain
#
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
jtag_nsrst_delay 300
jtag_ntrst_delay 200
jtag_rclk 3
######################
# Target configuration
######################
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm926ejs
# Internal sram1 memory
$_TARGETNAME configure -work-area-phys 0x00300000 -work-area-size 0x10000 -work-area-backup 1
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment